|
||||
| FORM-COAT PLYWOOD FORM COATING |
|
Forms sealed with "Form-Coat" permit easier stripping and do not show wood grain marks on the smooth concrete walls. It dries rapidly, giving gloss smooth surface
to the wood forms. Applied by brush, roller or dipping. Forms are completely sealed against moisture and can _be used repeatedly, thus saving more than the cost of the "Form-Coat"
Two coats recommended for application by brush, roller one for dipping. One gallon will cover 200 sq. ft. Reduces or eliminates costly rubbing of the stripped concrete.
"Form-Coat" is especially formulated to resist alkalies of concrete. Avoid any material that is non-alkali resistant. Has produced outstanding results on concrete
structures in all parts of the country. "Form-Coat" has a lacquer base-no other material can protect plywood, or give as smooth a surface on concrete, as can a hard lacquer.
|
| METALOID METALLIC FLOOR HARDENER (Return to Top Menu) |
|
"Metaloid" is a water absorbent, properly graded metallic hardener, containing a scientific dispersing agent, which permits the working of larger amounts of "Metaloid" into the floor.
It does not contain excessive proportions of fine iron dust present in many metallic hardeners, the jagged and irregular particles in "Metaloid" assure maximum bonding area with the cement
particles. It is completely free of oils, grease, aluminum or foreign matters that would interfere with the ready absorption in the slab. "Metaloid" withstands the heaviest industrial use
and is unaffected by acids and alkalies.
Specifications: After the concrete slab or top coat has been straightedge, apply a dry mixture of two parts "Metaloid" Metallic Hardener and one part cement, as evenly as possible, in two dust coats. Work both dustcoats into the floor with a power float, and finish with a steel hand trowel so that the floor is smooth. And free from defects of any kind. Apply (60 to 120) pounds of "Metaloid" per 100 square feet of floor. Depending on the use of the particular area. Colored "Metaloid" Hardener is available in any standard color and is used where a decorative heavy-duty floor is desired. Application is the same as for uncolored "Metaloid." Metaloid Metallic Floor Hardener is also available in premixed form: just open bag and apply to surface. |
| METALOID SPARK PROOF FLOOR HARDENER (Return to Top Menu) |
|
A "Metaloid" Spark proof Conductive Metallic Hardener floor will not spark when sharp contact is made with a steel wheel or other metal. Application is the same as the regular heavy duty "Metal-aid" Metallic Hardener. In plain and all
standard colors. Used extensively in arsenals and munitions buildings where it is essential to control static.
|
| CRYSTALOID LIQUID CEMENT FLOOR HARDENER (Return to Top Menu) |
|
"Crystaloid" Floor Hardener combines with certain elements in the cement to complete the hydration of the cement mixture, and to form hard, insoluble crystals in the pores of the floor which strengthens the wearing surface to withstand heavy traffic.
It can be applied to new or old floors. "Crystaloid" is made to penetrate deeper than most liquid hardeners, and quickly overcomes any resistance to absorption and penetration. One gallon of hardener will cover 100 square feet, three coats; Floors
with a good hard-troweled finish may need only two coats.
|
| DIAMOND-CRETE NON-SLIP FLOOR HARDENER (Return to Top Menu) |
|
A non-metallic colored or uncolored hardener to be used where a non-slip and non-rusting surface is of great importance. Resistant to acids, grease and alkalies, Used especially in manufacturing and food processing plants, hospitals, schools.
Apply as it comes from the container without adding any other material As little as 35 pounds per 100 square feet is sufficient for certain light conditions. For severe wear, use 50 to 80 pounds per 100 square feet. Float two dustcoats of "Diamond-Crete" into the floor and finish with a steel trowel. On interior colored "Diamond-Crete" floors, apply "Diamond Crete" liquid sealer of matched color, as soon as the floor can be walked on without damage, then cover with building paper. |
| LATEX CONCRETE TOPPING RESURFACER (Return to Top Menu) |
|
For resurfacing concrete that is worn, pitted or rough, smoothing, or patching any masonry surface. Will withstand heavy traffic. "Latex" Resurfacer bonds to old clean surfaces without chipping-can be used indoors or outdoors and is the color of ordinary concrete.
Resists many chemicals, oils, acids, grease.
Applied as thin as 1/16 inch or up to one inch and more, on any clean sound surface, wet or dry. No priming is necessary. |
| EPOXY BOND BONDING COMPOUND (Return to Top Menu) |
|
"Epoxy-Bond" is especially formulated for easy use and insulation. Bonding new concrete overlays of Portland cement can be applied easily and economically by bonding it to the existing surfaces with "Epoxy-Bond."
|
| EPOXY BOND RESURFACER AND PATCHING (Return to Top Menu) |
|
A compound formulated to provide a heavy-duty industrial topping to new or old floors. Used as a patching compound for concrete, wood, or steel flooring. The compound is characterized by outstanding chemical and solvent resistance, hardness,
impact and tensile strength. Excellent adhesion to most materials of construction is obtained. "EpoxyBond" is used as a Resurfacer to make a concrete like material, cures rapidly, does not shrink and exhibits excellent resistance to impact and surface wear.
|
| KORUMDON NON-SLIP ABRASIVE GRITS (Return to Top Menu) |
|
Made of pure aluminum oxide grain, or of silicon carbide grain, which gives a slight glitter to the surface. Meets Federal specifications. Use 25 to 35 pounds per 100 square feet.
|
| FLEX-KRETE FLOOR RESURFACER (Return to Top Menu) |
|
"Flex-Krete" is mixed with sand, cement and water to produce a tough, resilient. Industrial floor. Excellent for patching and leveling factory floors. Can be used over crumbling concrete joints and troweled down to a feathered edge.
Can be used outdoors or indoors over wood, brick, stone, metal or concrete-and with steel floor grids. Also for leveling before installation of some decorative flooring, such as asphalt tile, etc.
|
| BON-KRETE BONDING COMPOUND (Return to Top Menu) |
|
Ill bond concrete to a smooth or rough clean surface. Brushed on any surface that needs repairing, leveling or resurfacing. Over old concrete (must be clean) apply one coat of liquid "Bon-Krete" and let dry about 20 minutes or until
the film becomes transparent Then apply new concrete and an unbreakable bond will be formed. One gallon covers about 200 square feet. Bonds concrete, stone, tile and similar surfaces.
|
| GLAZE-COAT CEMENT FLOOR FINISH (Return to Top Menu) |
|
Produces the most dustproof concrete floor known. Widely used in hospitals, institutions, office buildings and electrical power stations. Applied with a mop to the clean, dry floor in two coats. One-gallon covers 250 square feet, two coats.
Where an absolutely dustproof floor is a necessity. "Glaze-Coat" should be used. Many thousands of square feet of dustproof floors, without any maintenance costs have proven the value of "Glaze-Coat." |
| FERRO-BAR IRON WATERPROOFING (Return to Top Menu) |
|
A fine-mesh waterproofing iron to be used in sealing pores in masonry surfaces by the well-known iron method. Applied to the dampened surface by brush in three or more coats. Final coat is covered with either a protective brush coat of equal
parts cement and sand, or with a ½ inch cement and sand plaster coat. 25 pound covers 100 sq. ft. three coats. Dampen surface between each application.
|
| DRI-SEAL SILICONE EXTERIOR WATERPROOFING (Return to Top Menu) |
|
Prevents water from soaking into a masonry wall. Apply to clean dry masonry surface in one coat. One gallon covers 75 to 150 sq. ft. in one coat, depending on the porosity of the surface. Only extremely porous surfaces take two coats. "Dri-Seal"
is guaranteed not to change the color or texture of even the lightest shades of masonry or limestone.
Contains the maximum percentage of silicones as recommended by the silicone manufacturer. Apply "Dri-Seal" with a brush or low pressure spray in such a way that a run down of 6 to 8 inches is obtained. Permits the wall to breathe. Efflorescence will not appear on a wall that has been treated with "Dri-Seal" because water cannot get into the wall to bring out the soluble salts that cause efflorescence. "Dri-Seal" is nontoxic, and easy to apply. Federal speo. SS-W-OOIIO, including revisions (GSA-FSS). |
| SUPER-MIX INTEGRAL WATERPROOFING (Return to Top Menu) |
|
Produces dense, waterproof concrete and mortars. 1. Requires less water to mix dry materials, thus minimizing shrinkage. 2. Lubricates the mix, making a more compact mass, with fewer voids. 3. Permits the cement to "coat" all aggregates. 4. Fills the microscopic voids with an insoluble water repellent compound. In liquid form, use one gallon per cubic yard of concrete, or 1 ½ gallons per cubic yard where severe water pressure is anticipated. |
| NON-METALLIC DIAMOND CRETE GROUT (Return to Top Menu) |
|
A non-metallic grouting compound composed of specially selected silica sands conforming to Federal Specification CRD-C 621-80, Portland Cement,
pozzualonic, plasticizing, water reducing and shrinkage compensating agents. The combination of the above ingredients produces in Diamond-Crete,
high early and 28 day strength and a slight but positive expansion right from time of placement with no intermediate shrinkage occurring.
Expansion is a mass expansion-therefore final volume filled is not affected by restraining such as with gas evolution or gas liberation-type
grouting compounds. Non-staining-can be pumped, dry packed and vibrated. Penn Dot approved for Pennsylvania projects.
|
| SHRINK PROOF GROUT (Return to Top Menu) |
|
A metallic aggregate with dispersing agent in powder form used in grouting between prestressed concrete beans, under machinery bases, column hases,
for patching disintegrated concrete walls and floors, etc. For one-inch clearance or over, for grouting anchor bolts, building columns, or bridge seats,
use equal parts "Shrinkproofer," sand and cement. For over one inch clearance if fine stones do not hinder free passage, add 1'2 parts grit to the above mix.
Sets in about eight hours. Produces seven-day strength in first 24 hours, with at least 50% greater ultimate strength.
CSMC Shrink proof Grouting is also made in premixed form, requiring only the addition of water, to obtain excellent results regardless of the suitability of local materials. |
| ANTI-SPALLING COMPOUND (Return to Top Menu) |
|
CSMC Anti- Spalling Compound protects concrete surfaces in two ways:
1. By Penetrating the porous surfaces of the concrete to a depth of approximately 1/8 inch. 2. By combining with atmospheric oxygen to form a protective coating through which destructive moisture and salt solutions can not penetrate. |
| C-H-S FLOOR TREATMENT WATER BASE (Return to Top Menu) |
|
CHS Water Base Floor treatment consists of a styrene-acrylate copolymer. It is used in curing, sealing, dustproofing, and hardening concrete.
CHS Water Base is suitable for use on new or old concrete and can be used indoors or outdoors without the adverse effects of a solvent based.
|
| WATER BASE CLEAR CURE-SEAL CURING COMPOUND S/S (Return to Top Menu) |
|
Cure-Seal Curing Compound was specifically formulated to cure and dustproof new and old concrete surfaces at one time and with one coat.
This multi-action product gives the concrete a hard, dust free surface that is resistant to oil and grease staining. Provides a surface to
which paint and resilient flooring mastic will bond securely.
|
| POLYURETHANE COATING (Return to Top Menu) |
|
Aromatic Moisture-Cure Urethane A true polyurethane coating of very high quality. Not modified or extended. Contains no drying oils and is ready to use. Performs like a two part system when it is a one-component urethane pre polymer, which cures by reaction with ambient moisture in the air to a moderately hard clear film with outstanding abrasion resistance, toughness, and flexibility. The coating is also resistant to the splash and spill of many oils, fats, chemicals, and solvents. The wear is sharply reduced and clean up is made easier. |
| CRYSTALOID "SH" - SURFACE HARDENER AND WATERPROOFER (Return to Top Menu) |
|
Crystaloid "SH" is a colorless, odorless, impregnating liquid for use on surfaces of concrete, rendering brick, limestone, or cast stone to produce a hard
protective surface. It produces an ideal protection for outside walls, counteracting the effects of corrosive atmospheres. Reduces and minimizes efflorescence.
|
| MULTI-PURPOSE NON-SHRINK NON-METALLIC GROUT (Return to Top Menu) |
|
CSMC Multi-Purpose grout is a general purpose, non-shrink, non-ferrous grout that is easily mixed for grouting at any consistency; dry pack, plastic or
pour able. It contains no iron particles chlorides or gypsum, and will not corrode, shrink, rust or ravel even under consistently moist conditions.
When mixed according to the instructions, it produces a high compressive strength due to a technology that reduces the water/cement ratio.
PRODUCT FEATURES One-step, ready to use. Just add water. High density - increases bond to metal, wood and other materials. Will not rust, bleed or harm materials it contacts. Requires no special treatment on open ends, or edges no capping or cutbacks. Clean finish - may be coated, trowel-finished, or painted. Density increases wear ability and permeability: withstands heat and thermal shock. Water tight-resists freeze, thaw, and water conditions and salt penetration. Resists a variety of oils and chemicals. Contains no free lime - will not produce efflorescence. |
| EPOXY-BOND COATINGS TYPE P (Return to Top Menu) |
|
These coatings are characterized by their outstanding resistance to many chemicals and solvents, excellent adhesion, flexibility, hardness, high
impact and abrasion resistance. Used for industrial and institutional maintenance and construction; where "baked on" quality is desired
from a room temperature cured system. Can be applied to wood, metals, masonry, ceramics, and glass. Available in clear, white, and many other colors.
The appearance will be a hard, smooth, title like surface. The gloss is medium to high. The coating is supplied in two parts, A and B, which are mixed
together in equal volumes, just prior to use. Enough coating is mixed to supply material, for a 4-hour application period. Quantities up 4 gallons
can be mixed in one container, but should be poured into containers holding no more than 1 gallon, after the blend is made. Reducing with recommended
thinners or storing at lower temperatures increases Pot-life.
|
| FORM SEAL FORM RELEASE AGENT (Return to Top Menu) |
|
Form Seal Release Agent is a ready to use liquid blend of natural organic chemicals. It reacts on contact with the alkali in the cement paste of the concrete to create a film between the form and the concrete surface. This chemical reaction permits easier stripping and cleaning of the forms and increases the coverage per gallon per that of normal form oils. Form seal release agent lengthens the life of wood forms by preventing the penetration of water; thus, reducing the deterioration of the plywood and lengthening the life of steel forms by preventing corrosion of the surface.
|
| FORM SEAL NON-STAINING FORM OIL (Return to Top Menu) |
|
Form Seal is a clean, non-staining, mineral paraffin base oil that is applied to plywood forms against which concrete is to be applied. Form Seal helps to produce a smoother concrete surface and has no adverse effects on the concrete. Form Seal makes forms easy to strip, leaving no deposits on the concrete. Form Seal will not stop all together, but will greatly reduce transfer of wood grain markings onto the concrete.
|
| FORM SEAL RELEASE AGENT WATER BASE (Return to Top Menu) |
|
Water Base Form Seal Release Agent is a tan opaque thin liquid, effective form release agent for wood, plywood, fiberglass, fiber tubes, metal, and plastic forms. Blends of natural organic chemicals, it provides a waterproof film to prevent adhesion of wet concrete to the forms and then an effective and easy release when removing the forms. It is manufactured for ready to use at the job site. It reduces the deterioration of forms and lengthens the life of the forms by protecting the surface in direct contact with the concrete. The wood forms life is increased and minimizes steel form corrosion.
|
| POOLTEX SPECIAL MIX CONCRETE FLOOR ENAMEL TRAFFIC GRADE (Return to Top Menu) |
|
Pooltex Special Mix Concrete Floor Enamel is recommended for protection of interior and exterior concrete and wood floors that take hard wear and weather. Resists oil penetration and is available in many colors. It can be applied to metal floors, decks, railings, stairs, columns, and baseboards.
|
| POOLTEX SPECIAL MIX SWIMMING POOL ENAMEL (Return to Top Menu) |
|
A scientific and proven material designed especially for use on new or old pools that have, either never been painted or have been coated with an oil-base swimming pool paint, or the ordinary pool enamel. Pooltex Special Mix Swimming Pool Enamel is successful because it has a perfectly balanced pigment content in conjunction with a perfected natural pliolite rubber base. The special vehicle penetrates into the pores of the concrete and accounts for the incredible durability. It provides a decorative tile-like finish that will help keep your pool cleaner, longer.
|
| LIQUID BUBBLE GUM RELEASE (Return to Top Menu) |
|
CSMC Clear Liquid Bubble Gum Release produces a clean separation agent between stamp tools and poured or polymer overlay concrete. It produces a clean alternative to powder release agents when only one stamp color is used. It also decreases friction between concrete and stamping tools. Ideal for interior use where powder is prohibited.
|
| EBONITE TROWEL GRADE FOUNDATION COATING (Return to Top Menu) |
|
Ebonite Trowel grade is manufactured from a blend of selected asphalts, stabilizers, fibers, and solvents. Ebonite Trowel is a heavy bodied product, which dries to a tough, flexible protective coating. It is highly resistant to the penetration of water and moisture over a wide range of temperature and service conditions. Has excellent resistance to most acid, alkali, and salt spray solutions.
|
| EBONITE BRUSH GRADE-ON FOUNDATION COATING (Return to Top Menu) |
|
Ebonite Brush-on grade is prepared to semi-mastic consistency for easy application, by brush, roller, or spray. This material is a multi-purpose, cold applied protective coating that dries to a tough, durable and flexible surface that give excellent performance over a wide array of temperatures and conditions. This product exhibits excellent resistance to acids and alkalies in the soil and the environment.
|
© 2006 Concrete Service Materials Company Designed by Ethan Heffler